FAQ: What Length Pulls To Use On Kitchen Cabinet?

What is the standard size for kitchen cabinet pulls?

For standard size cabinetry (dimensions of 12″ – 36″) the most common pull sizes are 3”, 4”, 96mm, and 128mm center to center (from one screw hole to another). Standard knob sizes are 1 1/4″ or 1 3/8″.

What size handles for 36 inch cabinets?

Cabinet doors 24-36 inches tall are best adorned with pulls 7-12 inches long, while cabinets taller than 36 inches such as pantries, built-in appliances and pullouts should be accompanied by pulls longer than 12 inches.

How do you measure for cabinet pulls?

Place the drawer pull on a work surface with the threaded posts facing up. Measure from the center of the screw hole in one threaded post over to the center of the other screw hole with a tape measure. This is the measurement required when selecting replacement pulls.

Where do you put long handles on kitchen cabinets?

Cabinet knobs are placed opposite of door hinges. On wall cabinets, knobs are usually placed 2-1/2” to 3” from the bottom corner of the door. On base cabinets, they are placed 2-1/2” to 3” from the upper corner of the door. If your drawer is 24” or wider, you may choose to place a second knob.

You might be interested:  Quick Answer: Where Can I Buy Grey Kitchen Cabinet Doors Only?

Should I use knobs or pulls on kitchen cabinets?

Should I use knobs or pulls on kitchen cabinets? Knobs can be the more comfortable option for cabinet doors because your hand rotates naturally as you open them. Pulls are a great option for drawers because your hand doesn’t have to rotate, and you can use more force underneath the whole pull.

Where should Pulls be placed on cabinets?

For both upper and lower cabinets, the pulls should be installed vertically 2 ½ – 3 inches in from the corner of the door. For drawers, they should be installed horizontally in the center of the door. While there is no hard-set rule for the size of your pulls, consider using longer ones on larger drawers and cabinets.

Can you use different size pulls on cabinets?

There is no right or wrong size to choose, but we do recommend choosing pulls that have at least a 3-3/4″ center to center (the distance between the screw holes). This size looks pleasing on most cabinets, while still being large enough to grip comfortably. 5″ pulls are also an excellent choice.

Should cabinet pulls be vertical or horizontal?

The thing to keep in mind with cabinet pulls has to do with placing them vertically or horizontally. Usually for cabinet door pulls, we recommend placing the pulls vertically, making it easy to open the doors (again, functionality is key).

Do you put pulls on fake drawers?

I would recommend putting pulls on the dummy drawers it allows for consistency. Good design is always consistent. It will also give the illusion that these drawers are not fake. The idea of putting a minimal intrusive towel bar works well because then it will serve more for function then aesthetics.

You might be interested:  Quick Answer: How To Locate Kitchen Cabinet Hardware?

What size drawer needs two pulls?

Drawers wider than 18″ need two knobs/pulls, whereas drawer narrower need only one. If a drawer is wide enough to need two knobs, they should be set about 1/6th of the drawer length from each end (roughly). Single pulls or knobs on drawers should be laterally centered and slightly higher than vertical center.

Can you put cup pulls on cabinet doors?

Pulls are another versatile option that can be installed on both cabinets and drawers. For both upper and lower cabinets, the pulls should be installed vertically 2 ½ – 3 inches in from the corner of the door. Just make sure not to drill any holes in your cabinetry until your mind is made up!

How do you open kitchen cabinets without handles?

Installed on the inside of your cabinets, a push latch is a mechanical (or magnetic) device that allows you to simply press on the cabinet door and have it spring open. No hardware is visible at all, and it will work with any most any cabinets.

Leave a Reply

Your email address will not be published. Required fields are marked *