Question: What Is A Rail Edge On A Kitchen Cabinet?

What is cabinet edge molding?

As you shop for new kitchen cabinets, or ways to improve existing cabinets, keep edge molding at the front of your mind. Cabinet edge molding refers to any molding that adorns a cabinet edge, such as crown, light rail and shelf molding. Typically, it’s made of wood, plaster or some other engineered material.

What is the rail on a cabinet?

Rail – A horizontal framing member of a cabinet face frame or door. Reveal – On a framed cabinet, the distance between the outside edge of the face frame and the outside edge of the door. Stile – The vertical-framing members of a cabinet face frame or cabinet door.

What are the parts of a cabinet called?

Cabinet Components

  • Cabinet Components. A kitchen cabinet is a simple wood box.
  • Cabinet Face Frame. Cabinet face frames provide stability, keeping the cabinet box square during shipping and installation.
  • Doors and Drawer Fronts.
  • Hinges.
  • Drawer Glides.
  • Drawer Box.
  • Interior Finish Material.
  • Cabinet Shelves.
You might be interested:  Quick Answer: How To Make Kitchen Cabinet Wood Look Fresh?

What is the molding on top of kitchen cabinets called?

Crown molding is decorative trim that is added to the top of your cabinets. The benefit of installing crown molding is that it draws the eye upward, showcasing the elegance of your cabinets. Crown molding can either bond with the ceiling or allow for space above the cabinet.

Is crown molding necessary on kitchen cabinets?

Crown molding is an iconic look for traditional cabinets. Without it, wall cabinets are typically left incomplete and need the finished look. This applies to kitchens that can afford to have the molding installed.

Do you put trim behind cabinets?

Behind the cabinets, the molding is not installed. The cabinets butt against the wall and the shoe molding is terminated at the edge of the cabinet. Install shoe molding behind the refrigerator. The base molding behind the cabinets needs removing as well.

What is the top rail of a cabinet?

In a cabinet frame, the top and bottom horizontal pieces are referred to as the rails. A rail is the horizontal portion of a cabinet frame. Rails are combined with the vertical pieces of wood, which are known as the stiles.

What are the vertical members of a cabinet door frame called?

The vertical members of the frame are called stiles while the horizontal members are known as rails. A basic frame and panel item consists of a top rail, a bottom rail, two stiles, and a panel. This is a common method of constructing cabinet doors and these are often referred to as a five piece door.

You might be interested:  Quick Answer: What Are Kitchen Cabinet Consumers Looking For?

How thick should cabinet face frames be?

Stiles and rails for doors and face frames are always the same thickness, typically 3/4 inch, according to Remodel-a-Holic. It’s standard for all cabinets and doors due to the fact that most cabinet-grade lumber of any type is 3/4 inch thick.

What are the 5 parts of the cabinet door?

Anatomy of a Cabinet Door

  • Panel – The center section of a cabinet door.
  • Rail – The top and bottom pieces in the frame.
  • Stile – The left and right pieces in the frame.
  • Outside Edge – The outside edge of the cabinet door.
  • Inside Edge – The inside edge of the cabinet frame.

What is the space under cabinets called?

That small area under the kitchen cabinets where your foot goes is called the “toe space” or “toe kick”. The toe space (also called a toe kick) needs attention too when installing kitchen cabinets. The toe space is made by a separate, recessed platform that supports the kitchen cabinet.

What is a cabinet base called?

Sometimes called floor or lower cabinets, base cabinets are the lower section of cabinetry that is installed on the floor. Makes sense, right? They are almost always capped off with a countertop of some sort, and are usually 24” deep and 36” high in American kitchens.

Do you put quarter round around cabinets?

If you have installed a new floor and there are gaps between the floor and the cabinets, quarter round molding can be installed to cover any gaps or imperfections. The molding can be nailed to the cabinets and stained or painted any color you like.

Leave a Reply

Your email address will not be published. Required fields are marked *