Readers ask: How To Determine Best Size Of Pull For New Kitchen Cabinet Door Handle?

What is the most popular cabinet pull size?

For standard size cabinetry (dimensions of 12″ – 36″) the most common pull sizes are 3”, 4”, 96mm, and 128mm center to center (from one screw hole to another). Standard knob sizes are 1 1/4″ or 1 3/8″.

What size pulls for 36 inch cabinets?

Pulls 3-7 inches in length will sit the most comfortably on doors less than 24 inches tall. Cabinet doors 24-36 inches tall are best adorned with pulls 7-12 inches long, while cabinets taller than 36 inches such as pantries, built-in appliances and pullouts should be accompanied by pulls longer than 12 inches.

What is the standard size drawer pull?

Standard Drawers (about 12″ – 36″) Standard-sized drawers can use any of the following pull sizes: 3” (one or two), 4” (one or two), 96mm, and 128mm.

How do you measure for a new cabinet door handle?

Measure the distance between the two screws from the centre of each screw. This will give you your ‘fixing centres’ and is the measurement you need when buying your new handles. Our handles are all listed with a measurement appended to the title. This measurement is the ‘fixing centre’, NOT the total length.

You might be interested:  Question: How To Clean Kitchen Hardwood Cabinet Doors?

Should all cabinet pulls be same size?

Consistent Size Throughout There is no right or wrong size to choose, but we do recommend choosing pulls that have at least a 3-3/4″ center to center (the distance between the screw holes). This size looks pleasing on most cabinets, while still being large enough to grip comfortably.

Should cabinet pulls be vertical or horizontal?

The thing to keep in mind with cabinet pulls has to do with placing them vertically or horizontally. Usually for cabinet door pulls, we recommend placing the pulls vertically, making it easy to open the doors (again, functionality is key).

Can you mix cabinet pull sizes?

Although it’s definitely possible to coordinate cabinet hardware in different finishes, it’s much easier and safer to mix different shapes of knobs and pulls in one matching finish.

Where should Pulls be placed on cabinets?

For both upper and lower cabinets, the pulls should be installed vertically 2 ½ – 3 inches in from the corner of the door. For drawers, they should be installed horizontally in the center of the door. While there is no hard-set rule for the size of your pulls, consider using longer ones on larger drawers and cabinets.

How are cabinet pulls measured?

The Center-to-Center of any drawer pull is the distance between the center of one screw hole to the center of the other. Measuring the center-to-center of the drawer pull is key in determining what new hardware will fit and whether you’ll need to drill new mounting holes or fit into existing ones.

You might be interested:  Readers ask: How To Kitchen Grime From Cabinet Handles?

What size drawer needs two pulls?

Drawers wider than 18″ need two knobs/pulls, whereas drawer narrower need only one. If a drawer is wide enough to need two knobs, they should be set about 1/6th of the drawer length from each end (roughly). Single pulls or knobs on drawers should be laterally centered and slightly higher than vertical center.

How do you measure for new drawer pulls?

Place the drawer pull on a work surface with the threaded posts facing up. Measure from the center of the screw hole in one threaded post over to the center of the other screw hole with a tape measure. This is the measurement required when selecting replacement pulls.

Do you put pulls on fake drawers?

I would recommend putting pulls on the dummy drawers it allows for consistency. Good design is always consistent. It will also give the illusion that these drawers are not fake. The idea of putting a minimal intrusive towel bar works well because then it will serve more for function then aesthetics.

Are kitchen door handles standard sizes?

Standard pull handles tend to range between 3 and 4 inches (96 to 128mm) in width, with smaller T-pulls often used for small cabinets and drawers. As a rule of thumb, the larger the drawer or cabinet, the larger the handle should be.

Leave a Reply

Your email address will not be published. Required fields are marked *